(DISCONTINUED) Honeywell Voyager MS9520 Wired Barcode Scanner Configuration

(DISCONTINUED) Honeywell Voyager MS9520 Wired Barcode Scanner Configuration

Honeywell Voyager MS-9520 USB Barcode Scanner Configuration Guide (Discontinued Model)

 

For USB port connections:

 

Plug the end of the barcode scanner cable into an available USB port on your computer.

The barcode scanner should beep to let you know that it is now active. No software driver

is required for your barcode scanner.

 

Prior to using your bar code scanner, you must configure it for use within your software. To do so,

you must print this page and scan the items below in order. Please note: You MUST print this

sheet, as you will be unable to scan the code on the screen and normally requires a laser printer to print codes clear enough to scan.


Scan this barcode to enter configuration mode. The barcode scanner should beep three times to

let you know it has entered the configuration mode.

 voyager 9520 enter config mode



Scan this barcode to disable the carriage return suffix:

 voyager 9520 disable carriage return



Scan this barcode to disable the line feed suffix:

 voyager 9520 disable line feed suffix



Scan this barcode to enable the tab suffix:

 voyager 9520 enable tab suffix





To exit the configuration mode, scan this barcode. The barcode scanner should beep three times

to let you know it has exited the configuration mode. This barcode is the same as the very first

barcode in this document.

 




Your barcode scanner should now be configured to properly work within your software.

If you have any questions or concerns about the installation and configuration of your barcode

scanner, or have any difficulties with any of these instructions, please don’t hesitate to call our

technical support department at 888.486.4343. This concludes the Barcode Scanner

Installation Guide.





 stop


SCANNING THE BARCODE BELOW WILL RESET YOUR BARCODE SCANNER TO FACTORY DEFAULT. THIS IS NOT TO BE DONE NOW.



If necessary, to restore the barcode scanner to its factory-default settings, scan the following

barcode. Important! Scanning this barcode will eliminate any programming changes you already

made, and you will need to reprogram your barcode scanner. It will stop working properly with Kennel Connection if you proceed.

reset to default 



Helpful Hints:

 

  • In KC, make sure to go into File, System options, Local tab and enable your barcode scanner and options in the lower right-hand corner.

 

  • If using this barcode scanner for scanning pet key tags into daycare and you want it fully automated, be sure to go into File, System Options, Daycare and place a check mark next to “Auto-create booking and Check-in.”

 

  • If your barcode scanner is NOT scanning anything into Kennel Connection at all, open Notepad on your computer and make sure the cursor is flashing in there. Scan a barcode. If the barcode shows up in notepad, your device may not be configured to properly work with Kennel Connection. Please try the “Add tab suffix” scan again. IF nothing scans into notepad, there is a hardware issue within that device. Please try a new USB port or a different computer. If it still fails, you’ll need to contact the vendor.
    • Related Articles

    • (DISCONTINUED)Honeywell Voyager 1202g WIRELESS Barcode Scanner Configuration Instructions

      Honeywell Voyager 1202g WIRELESS Barcode Scanner Configuration Instructions Here are the instructions for programming your wireless barcode scanner.  Print out this barcode sheet before proceeding: ...
    • Barcode Scanner Installation Guide KC7

      Barcode Scanner Installation Guide KC7 You can use the barcode scanner for two purposes:  You can scan retail items onto an invoice instead of searching for the code and you can automatically create appointments and check the pet in/out for the ...
    • (DISCONTINUED) Honeywell Voyager 1200g Programming Guide

      Honeywell Voyager 1200g Programming Guide Important: You may need to print this guide on a laser printer to scan correctly.    Unlike previous models, the new Voyager 1200g comes with most of the required settings already set for Kennel Connection ...
    • Zebra DS2208 Barcode Scanner Setup

      ​ This 2D scanner is designed for all types of retail environments and scans very aggressively at all angles, in all light conditions, and on most forms of media including cell phone screens. This scanner was built with future proofing in mind where ...
    • Barcode scanner is not working for check-ins

      Remedy 1:  Be sure Kennel Connection is set to accept checkins with the scanner.  Click on File, System Options, Local tab. Check each box to set your preferences.  Be sure to hit Apply when done. Remedy 2:  The scanner must be configured properly. ...